Astra
Full Member
Posts: 219 
|
Post by Astra on Apr 28, 2018 10:26:13 GMT
Hi Guy's they are already gate valve types fitted and have already checked in van there are a pair of 28mm valves ready and waiting if needed..........
Can not wait till Thursday Deep Joy NOT !!!!!!
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Apr 28, 2018 12:55:33 GMT
Hi Guy's they are already gate valve types fitted and have already checked in van there are a pair of 28mm valves ready and waiting if needed.......... Can not wait till Thursday Deep Joy NOT !!!!!! You never want to work yourself up about a job you've got to do Astra mate it's unhealthy  I know we are all different but I don't really think about a job untill I'm there doing it. I hope it all goes ok for you.  |
|
|
|
Post by endfeed on Apr 28, 2018 13:06:49 GMT
Good advice,p.b! I'm bit of a worrier before hand if its a shitter of a job!when it's done I think what the fook was worried about!!!¡!
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Apr 28, 2018 13:41:24 GMT
Good advice,p.b! I'm bit of a worrier before hand if its a shitter of a job!when it's done I think what the fook was worried about!!!¡! That's the trouble endfeed people get worked up and quite often it's about nothing  |
|
Astra
Full Member
Posts: 219
|
Post by Astra on Apr 28, 2018 18:20:01 GMT
Thanks for the kind words Guy's but we can not help the way we are all made ,,,,,All different i use to be a lot worse
but as you say once you get into it and the old Grey matter kicks in it generally all works out and yes you are right
at the end you look round at yourself and say WTF was I worried about Cheers Guy's many thanks appreciate it.........
|
|
|
|
Post by arfur chrysaik on Apr 28, 2018 21:35:21 GMT
Tell me about it , just hoping that if I cannot get enough pipe spread to fit new pump and washers Was thinking about drain down then cutting through that 28mm pipe as in my photo ,,then hopefully be able to get enough space to do the deed then just put a 28mm comp joint on to reseal the pipe back..... If it's a brick wall at the back, shut the gate valves and loosen the pump nuts a couple of turns, then knock an old long screwdriver 1/2" into the wall underneath the top gate valve body, then lever it up about 1/4" and jam a bit 2x1" under the screwdriver handle then you can work at the pump with both hands, fuck draining down when you don't need to. |
|
|
|
Post by tomplum on Apr 28, 2018 22:11:45 GMT
good tip from arfur there,  |
|
Astra
Full Member
Posts: 219
|
Post by Astra on Apr 30, 2018 11:08:02 GMT
Hi Arfur wish it was a brick wall !! just my luck this one is plaster board Great !!!
|
|
|
|
Post by arfur chrysaik on Apr 30, 2018 21:01:24 GMT
Hi Arfur wish it was a brick wall !! just my luck this one is plaster board Great !!! Slip an old bit of skirting vertically down the back of the pipes to the floor then do as mentioned before. |
|
|
|
Post by tomplum on Apr 30, 2018 21:06:36 GMT
a good tip with a back up plan,,,you'll only get stuff like this here, thanks arfur,,  |
|
Astra
Full Member
Posts: 219
|
Post by Astra on May 1, 2018 16:35:44 GMT
Hi Arfur Many thanks for the tip very very good you definatley know your stuff that gives me some hope now thank you....
You have obviously been there yourself Ah Just a few times !!!!! I bet.......
Now all I need is to be quickly cross trained to become a chppy so I can cut the wood !!!!!
|
|
I know we are all different but I don't really think about a job untill I'm there doing it.
